TEXTURES OF HOT-ROLLED AND COLD-ROLLED ZINC AND ZINC ALLOYS. INFLUENCE OF RECRYSTALLISATIONMESSIEN P; WEGRIA J.1972; METALLURG. REP. C.R.M.; BELG.; DA. 1972; NO 32; PP. 61-74; ABS. FR. ALLEM. NEERL.; BIBL. 13 REF.Serial Issue

ETUDE PAR FROTTEMENT INTERNE DE LA SEGREGATION INTERGRANULAIRE DANS LES ALLIAGES FER-AZOTE DE HAUTE PURETEWEGRIA J; GOUZOU J; HABRAKEN L et al.1974; ; S.L.; DA. 1974; DE L'ANGL.: METALLURGICAL REPORTS C.R.M., JUIN 1973; NO 35, 51-61Miscellaneous

DETERMINATION, BY INTERNAL FRICTION MEASUREMENTS OF THE INTERSTITIAL NITROGEN CONTENT IN FE-MN-N ALLOYSGOUZOU J; WEGRIA J; HABRAKEN L et al.1972; METALLURG. REP. C.R.M.; BELG.; DA. 1972; NO 33; PP. 65-71; BIBL. 13 REF.Serial Issue

GENERALISATION DE LA LOI DE WERT ET MARX, ET FREQUENCE DE VIBRATION DES ATOMES EN SOLUTION INTERSTITIELLE DANS UN RESEAU CUBIQUE CENTREGOUZOU J; WEGRIA J; HABRAKEN L et al.1972; C.R. ACAD. SCI., C; FR.; DA. 1972; VOL. 275; NO 16; PP. 865-867; BIBL. 13 REF.Serial Issue

STUDY OF SHOULDER QUALITY OF PHOTOENGRAVING ALLOY = ETUDE DE LA QUALITE DU RELIEF DES ALLIAGES POUR LA PHOTOGRAVUREWEGRIA J; PICCININ A; RACEK R et al.1981; METALL. REP. CRM; ISSN 0026-0851; BEL; DA. 1981; NO 58; PP. 31-47; ABS. GER/FRE/FLE; BIBL. 23 REF.Article

STUDY OF DRAWABLE ZINC ALLOYS.PICCININ A; WEGRIA J; RACEK R et al.1977; METALLURG. REP. C.R.M.; BELG.; DA. 1977; NO 51; PP. 23-30; ABS. ALLEM. FR. NEERL.; BIBL. 10 REF.Article

ETUDE D'ALLIAGES DE ZINC POUR EMBOUTISSAGE.PICCININ A; WEGRIA J; RACEK R et al.sdIN: INT. CONF. STRENGTH MET. ALLOYS. 4. PROC.; NANCY; 1976; NANCY; ENSMIM-INPL; DA. S.D.; VOL. 2; PP. 659-663; BIBL. 6 REF.Conference Paper

INTERNAL FRICTION STUDY OF THE INFLUENCE OF TITANIUM CONTENT ON THE CREEP STRENGTH OF ZINC-TITANIUM ALLOYSGASPARD C; GOUZOU J; WEGRIA J et al.1975; METALLURG. REP. C.R.M.; BELG.; DA. 1975; NO 45; PP. 41-47; ABS. ALLEM. FR. NEERL.; BIBL. 19 REF.Article

CORRELATION BETWEEN SECONDARY CREEP AND GRAIN-BOUNDARY INTERNAL FRICTION IN ZINC AND ZINC ALLOYSGASPARD C; GOUZOU J; WEGRIA J et al.1974; METALLURG. REP.C.R.M.; BELG.; DA. 1974; NO 41; PP. 29-33; ABS. ALLEM. FR. NEERL.; BIBL. 6 REF.Article

APPARITION D'UN CROCHET A LA LIMITE D'ELASTICITE DE L'ALLIAGE ZINC-2,5% CUIVRE-0,15% TITANE APRES TRAITEMENT THERMIQUEWEGRIA J; PICCININ A; COSSE P et al.1979; MEM. SCI. REV. METALLURG.; FRA; DA. 1979; VOL. 76; NO 2; PP. 133-145; BIBL. 18 REF.Article

ON A YIELD POINT EFFECT APPEARING IN THE ALLOY ZN-2,5% CU-0,15% TI AFTER HEAT TREATMENTWEGRIA J; COSSE P; GOUZOU J et al.1978; METALLURG. REP. C.R.M.; BEL; DA. 1978; NO 53; PP. 33-46; ABS. FRE/GER/DUT; BIBL. 17 REF.Article

Influence of creep on the microstructure of Zn-Al-Cu alloys aged at 250°CTERZIEV, L; LECOMTE-BECKERS, J; WEGRIA, J et al.Physica status solidi. A. Applied research. 1995, Vol 152, Num 2, pp 405-413, issn 0031-8965Article

Etude des relations entre les micro-structures obtenues par vieillissement isotherme et le comportement mécanique (fluage, résilience) dans des alliages Zn-Al et Zn-Al-Cu = Correlation between the microstructures observed during isothermal ageing and mechanical behaviour in Zn-Al and Zn-Al-Cu alloysTERZIEV, L; LECOMTE-BECKERS, J; WEGRIA, J et al.Cahiers d'informations techniques de la revue de métallurgie. 1994, Vol 91, Num 5, V, VI, VIII, 789-798 [13 p.]Article

Addition elements and texture gradients in rolled zinc alloysDIOT, M; PHILIPPE, M. J; WEGRIA, J et al.Scripta materialia. 1999, Vol 40, Num 11, pp 1295-1303, issn 1359-6462Article

Zn-Al matrix composites : investigation of the thermal expansion, creep resistance and fracture toughnessDELLIS, M. A; KEUSTERMANS, J. P; DELANNAY, F et al.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 1991, Vol 135, pp 253-257, issn 0921-5093, 5 p.Conference Paper

Texture gradient in rolled zinc sheetsDIOT, M; FUNDENBERGER, J. J; PHILIPPE, M. J et al.Scripta materialia. 1998, Vol 39, Num 11, pp 1623-1630, issn 1359-6462Article

Comparison of fibres for creep strengthening of zinc-aluminium foundry alloysTAO, L; DELLIS, M.-A; BOLAND, F et al.Composites. 1995, Vol 26, Num 9, pp 611-617, issn 0010-4361Article